blob: 4f91686e54a6b939fc1b430f146149b125db173c [file] [log] [blame]
* Analog Devices ADV748X video decoder with HDMI receiver
The ADV7481 and ADV7482 are multi format video decoders with an integrated
HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB
from three input sources HDMI, analog and TTL.
Required Properties:
- compatible: Must contain one of the following
- "adi,adv7481" for the ADV7481
- "adi,adv7482" for the ADV7482
- reg: I2C slave addresses
The ADV748x has up to twelve 256-byte maps that can be accessed via the
main I2C ports. Each map has it own I2C address and acts as a standard
slave device on the I2C bus. The main address is mandatory, others are
optional and remain at default values if not specified.
Optional Properties:
- interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or
"intrq3". All interrupts are optional. The "intrq3" interrupt
is only available on the adv7481
- interrupts: Specify the interrupt lines for the ADV748x
- reg-names : Names of maps with programmable addresses.
It shall contain all maps needing a non-default address.
Possible map names are:
"main", "dpll", "cp", "hdmi", "edid", "repeater",
"infoframe", "cbus", "cec", "sdp", "txa", "txb"
The device node must contain one 'port' child node per device input and output
port, in accordance with the video interface bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
are numbered as follows.
Name Type Port
---------------------------------------
AIN0 sink 0
AIN1 sink 1
AIN2 sink 2
AIN3 sink 3
AIN4 sink 4
AIN5 sink 5
AIN6 sink 6
AIN7 sink 7
HDMI sink 8
TTL sink 9
TXA source 10
TXB source 11
The digital output port nodes, when present, shall contain at least one
endpoint. Each of those endpoints shall contain the data-lanes property as
described in video-interfaces.txt.
Required source endpoint properties:
- data-lanes: an array of physical data lane indexes
The accepted value(s) for this property depends on which of the two
sources are described. For TXA 1, 2 or 4 data lanes can be described
while for TXB only 1 data lane is valid. See video-interfaces.txt
for detailed description.
Ports are optional if they are not connected to anything at the hardware level.
Example:
video-receiver@70 {
compatible = "adi,adv7482";
reg = <0x70 0x71 0x72 0x73 0x74 0x75
0x60 0x61 0x62 0x63 0x64 0x65>;
reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
"infoframe", "cbus", "cec", "sdp", "txa", "txb";
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&gpio6>;
interrupt-names = "intrq1", "intrq2";
interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
<31 IRQ_TYPE_LEVEL_LOW>;
port@7 {
reg = <7>;
adv7482_ain7: endpoint {
remote-endpoint = <&cvbs_in>;
};
};
port@8 {
reg = <8>;
adv7482_hdmi: endpoint {
remote-endpoint = <&hdmi_in>;
};
};
port@a {
reg = <10>;
adv7482_txa: endpoint {
clock-lanes = <0>;
data-lanes = <1 2 3 4>;
remote-endpoint = <&csi40_in>;
};
};
port@b {
reg = <11>;
adv7482_txb: endpoint {
clock-lanes = <0>;
data-lanes = <1>;
remote-endpoint = <&csi20_in>;
};
};
};