blob: d4697396887387eefd1246e972a1c6c1e4b06374 [file] [log] [blame]
Qualcomm MDM9615 TLMM block
This binding describes the Top Level Mode Multiplexer block found in the
MDM9615 platform.
- compatible:
Usage: required
Value type: <string>
Definition: must be "qcom,mdm9615-pinctrl"
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: the base address and size of the TLMM register space.
- interrupts:
Usage: required
Value type: <prop-encoded-array>
Definition: should specify the TLMM summary IRQ.
- interrupt-controller:
Usage: required
Value type: <none>
Definition: identifies this node as an interrupt controller
- #interrupt-cells:
Usage: required
Value type: <u32>
Definition: must be 2. Specifying the pin number and flags, as defined
in <dt-bindings/interrupt-controller/irq.h>
- gpio-controller:
Usage: required
Value type: <none>
Definition: identifies this node as a gpio controller
- #gpio-cells:
Usage: required
Value type: <u32>
Definition: must be 2. Specifying the pin number and flags, as defined
in <dt-bindings/gpio/gpio.h>
- gpio-ranges:
Usage: required
Definition: see ../gpio/gpio.txt
- gpio-reserved-ranges:
Usage: optional
Definition: see ../gpio/gpio.txt
Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
a general description of GPIO and interrupt bindings.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
The pin configuration nodes act as a container for an arbitrary number of
subnodes. Each of these subnodes represents some desired configuration for a
pin, a group, or a list of pins or groups. This configuration can include the
mux function to select on those pin(s)/group(s), and various pin configuration
parameters, such as pull-up, drive strength, etc.
PIN CONFIGURATION NODES:
The name of each subnode is not important; all subnodes should be enumerated
and processed purely based on their content.
Each subnode only affects those parameters that are explicitly listed. In
other words, a subnode that lists a mux function but no pin configuration
parameters implies no information about any pin configuration parameters.
Similarly, a pin subnode that describes a pullup parameter implies no
information about e.g. the mux function.
The following generic properties as defined in pinctrl-bindings.txt are valid
to specify in a pin configuration subnode:
- pins:
Usage: required
Value type: <string-array>
Definition: List of gpio pins affected by the properties specified in
this subnode. Valid pins are:
gpio0-gpio87
- function:
Usage: required
Value type: <string>
Definition: Specify the alternative function to be configured for the
specified pins.
Valid values are:
gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart,
sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio,
cdc_mclk
- bias-disable:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as no pull.
- bias-pull-down:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as pull down.
- bias-pull-up:
Usage: optional
Value type: <none>
Definition: The specified pins should be configured as pull up.
- output-high:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
high.
- output-low:
Usage: optional
Value type: <none>
Definition: The specified pins are configured in output mode, driven
low.
- drive-strength:
Usage: optional
Value type: <u32>
Definition: Selects the drive strength for the specified pins, in mA.
Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
Example:
msmgpio: pinctrl@800000 {
compatible = "qcom,mdm9615-pinctrl";
reg = <0x800000 0x4000>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&msmgpio 0 0 88>;
interrupt-controller;
#interrupt-cells = <2>;
interrupts = <0 16 0x4>;
gsbi8_uart: gsbi8-uart {
mux {
pins = "gpio34", "gpio35";
function = "gsbi8";
};
tx {
pins = "gpio34";
drive-strength = <4>;
bias-disable;
};
rx {
pins = "gpio35";
drive-strength = <2>;
bias-pull-up;
};
};
};