blob: a61b3cc6f4c95ecf8396b1ff253fa1f794f10dd0 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP ZCU111
*
* (C) Copyright 2017 - 2018, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
/ {
model = "ZynqMP ZCU111 RevA";
compatible = "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111", "xlnx,zynqmp";
aliases {
ethernet0 = &gem3;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &dcc;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
/* Another 4GB connected to PL */
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
sw19 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
gpio-key,wakeup;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
heartbeat_led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
&dcc {
status = "okay";
};
&fpd_dma_chan1 {
status = "okay";
};
&fpd_dma_chan2 {
status = "okay";
};
&fpd_dma_chan3 {
status = "okay";
};
&fpd_dma_chan4 {
status = "okay";
};
&fpd_dma_chan5 {
status = "okay";
};
&fpd_dma_chan6 {
status = "okay";
};
&fpd_dma_chan7 {
status = "okay";
};
&fpd_dma_chan8 {
status = "okay";
};
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
};
};
&gpio {
status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
tca6416_u22: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller; /* interrupt not connected */
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - MAX6643_OT_B
* 1 - MAX6643_FANFAIL_B
* 2 - MIO26_PMU_INPUT_LS
* 4 - SFP_SI5382_INT_ALM
* 5 - IIC_MUX_RESET_B
* 6 - GEM3_EXP_RESET_B
* 10 - FMCP_HSPC_PRSNT_M2C_B
* 11 - CLK_SPI_MUX_SEL0
* 12 - CLK_SPI_MUX_SEL1
* 16 - IRPS5401_ALERT_B
* 17 - INA226_PMBUS_ALERT
* 3, 7, 13-15 - not connected
*/
};
i2c-mux@75 { /* u23 */
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* PS_PMBUS */
/* PMBUS_ALERT done via pca9544 */
ina226@40 { /* u67 */
compatible = "ti,ina226";
reg = <0x40>;
shunt-resistor = <2000>;
};
ina226@41 { /* u59 */
compatible = "ti,ina226";
reg = <0x41>;
shunt-resistor = <5000>;
};
ina226@42 { /* u61 */
compatible = "ti,ina226";
reg = <0x42>;
shunt-resistor = <5000>;
};
ina226@43 { /* u60 */
compatible = "ti,ina226";
reg = <0x43>;
shunt-resistor = <5000>;
};
ina226@45 { /* u64 */
compatible = "ti,ina226";
reg = <0x45>;
shunt-resistor = <5000>;
};
ina226@46 { /* u69 */
compatible = "ti,ina226";
reg = <0x46>;
shunt-resistor = <2000>;
};
ina226@47 { /* u66 */
compatible = "ti,ina226";
reg = <0x47>;
shunt-resistor = <5000>;
};
ina226@48 { /* u65 */
compatible = "ti,ina226";
reg = <0x48>;
shunt-resistor = <5000>;
};
ina226@49 { /* u63 */
compatible = "ti,ina226";
reg = <0x49>;
shunt-resistor = <5000>;
};
ina226@4a { /* u3 */
compatible = "ti,ina226";
reg = <0x4a>;
shunt-resistor = <5000>;
};
ina226@4b { /* u71 */
compatible = "ti,ina226";
reg = <0x4b>;
shunt-resistor = <5000>;
};
ina226@4c { /* u77 */
compatible = "ti,ina226";
reg = <0x4c>;
shunt-resistor = <5000>;
};
ina226@4d { /* u73 */
compatible = "ti,ina226";
reg = <0x4d>;
shunt-resistor = <5000>;
};
ina226@4e { /* u79 */
compatible = "ti,ina226";
reg = <0x4e>;
shunt-resistor = <5000>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* NC */
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
reg = <0x43>;
};
irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
reg = <0x44>;
};
irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
reg = <0x45>;
};
/* u68 IR38064 +0 */
/* u70 IR38060 +1 */
/* u74 IR38060 +2 */
/* u75 IR38060 +6 */
/* J19 header too */
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
/* SYSMON */
};
};
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
i2c-mux@74 { /* u26 */
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/*
* IIC_EEPROM 1kB memory which uses 256B blocks
* where every block has different address.
* 0 - 256B address 0x54
* 256B - 512B address 0x55
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
eeprom: eeprom@54 { /* u88 */
compatible = "atmel,24c08";
reg = <0x54>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u46 */
reg = <0x36>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
si570_1: clock-generator@5d { /* USER SI570 - u47 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
};
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>;
factory-fout = <156250000>;
clock-frequency = <148500000>;
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 { /* SI5328 - u48 */
reg = <0x69>;
};
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
sc18is603@2f { /* sc18is602 - u93 */
compatible = "nxp,sc18is603";
reg = <0x2f>;
/* 4 gpios for CS not handled by driver */
/*
* USB2ANY cable or
* LMK04208 - u90 or
* LMX2594 - u102 or
* LMX2594 - u103 or
* LMX2594 - u104
*/
};
};
i2c@6 {
#address-cells = <1>;
#size-cells = <0>;
reg = <6>;
/* FMC connector */
};
/* 7 NC */
};
i2c-mux@75 {
compatible = "nxp,pca9548"; /* u27 */
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* FMCP_HSPC_IIC */
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* NC */
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
/* SYSMON */
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
/* DDR4 SODIMM */
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
/* SFP3 */
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
/* SFP2 */
};
i2c@6 {
#address-cells = <1>;
#size-cells = <0>;
reg = <6>;
/* SFP1 */
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
/* SFP0 */
};
};
};
&rtc {
status = "okay";
};
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
no-1-8-v;
};
&uart0 {
status = "okay";
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
};