| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # HISILICON device configuration |
| # |
| |
| config NET_VENDOR_HISILICON |
| bool "Hisilicon devices" |
| default y |
| depends on OF || ACPI |
| depends on ARM || ARM64 || COMPILE_TEST |
| ---help--- |
| If you have a network (Ethernet) card belonging to this class, say Y. |
| |
| Note that the answer to this question doesn't directly affect the |
| kernel: saying N will just cause the configurator to skip all |
| the questions about Hisilicon devices. If you say Y, you will be asked |
| for your specific card in the following questions. |
| |
| if NET_VENDOR_HISILICON |
| |
| config HIX5HD2_GMAC |
| tristate "Hisilicon HIX5HD2 Family Network Device Support" |
| select PHYLIB |
| help |
| This selects the hix5hd2 mac family network device. |
| |
| config HISI_FEMAC |
| tristate "Hisilicon Fast Ethernet MAC device support" |
| depends on HAS_IOMEM |
| select PHYLIB |
| select RESET_CONTROLLER |
| help |
| This selects the Hisilicon Fast Ethernet MAC device(FEMAC). |
| The FEMAC receives and transmits data over Ethernet |
| ports at 10/100 Mbps in full-duplex or half-duplex mode. |
| The FEMAC exchanges data with the CPU, and supports |
| the energy efficient Ethernet (EEE). |
| |
| config HIP04_ETH |
| tristate "HISILICON P04 Ethernet support" |
| depends on HAS_IOMEM # For MFD_SYSCON |
| select MARVELL_PHY |
| select MFD_SYSCON |
| select HNS_MDIO |
| ---help--- |
| If you wish to compile a kernel for a hardware with hisilicon p04 SoC and |
| want to use the internal ethernet then you should answer Y to this. |
| |
| config HI13X1_GMAC |
| bool "Hisilicon HI13X1 Network Device Support" |
| depends on HIP04_ETH |
| help |
| If you wish to compile a kernel for a hardware with hisilicon hi13x1_gamc |
| then you should answer Y to this. This makes this driver suitable for use |
| on certain boards such as the HI13X1. |
| |
| If you are unsure, say N. |
| |
| config HNS_MDIO |
| tristate |
| select PHYLIB |
| ---help--- |
| This selects the HNS MDIO support. It is needed by HNS_DSAF to access |
| the PHY |
| |
| config HNS |
| tristate "Hisilicon Network Subsystem Support (Framework)" |
| ---help--- |
| This selects the framework support for Hisilicon Network Subsystem. It |
| is needed by any driver which provides HNS acceleration engine or make |
| use of the engine |
| |
| config HNS_DSAF |
| tristate "Hisilicon HNS DSAF device Support" |
| select HNS |
| select HNS_MDIO |
| ---help--- |
| This selects the DSAF (Distributed System Area Frabric) network |
| acceleration engine support. The engine is used in Hisilicon hip05, |
| Hi1610 and further ICT SoC |
| |
| config HNS_ENET |
| tristate "Hisilicon HNS Ethernet Device Support" |
| select PHYLIB |
| select HNS |
| ---help--- |
| This selects the general ethernet driver for HNS. This module make |
| use of any HNS AE driver, such as HNS_DSAF |
| |
| config HNS3 |
| tristate "Hisilicon Network Subsystem Support HNS3 (Framework)" |
| depends on PCI |
| ---help--- |
| This selects the framework support for Hisilicon Network Subsystem 3. |
| This layer facilitates clients like ENET, RoCE and user-space ethernet |
| drivers(like ODP)to register with HNAE devices and their associated |
| operations. |
| |
| if HNS3 |
| |
| config HNS3_HCLGE |
| tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support" |
| default m |
| depends on PCI_MSI |
| ---help--- |
| This selects the HNS3_HCLGE network acceleration engine & its hardware |
| compatibility layer. The engine would be used in Hisilicon hip08 family of |
| SoCs and further upcoming SoCs. |
| |
| config HNS3_DCB |
| bool "Hisilicon HNS3 Data Center Bridge Support" |
| default n |
| depends on HNS3_HCLGE && DCB |
| ---help--- |
| Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver. |
| |
| If unsure, say N. |
| |
| config HNS3_HCLGEVF |
| tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support" |
| depends on PCI_MSI |
| depends on HNS3_HCLGE |
| ---help--- |
| This selects the HNS3 VF drivers network acceleration engine & its hardware |
| compatibility layer. The engine would be used in Hisilicon hip08 family of |
| SoCs and further upcoming SoCs. |
| |
| config HNS3_ENET |
| tristate "Hisilicon HNS3 Ethernet Device Support" |
| default m |
| depends on 64BIT && PCI |
| depends on INET |
| ---help--- |
| This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08 |
| family of SoCs. This module depends upon HNAE3 driver to access the HNAE3 |
| devices and their associated operations. |
| |
| endif #HNS3 |
| |
| endif # NET_VENDOR_HISILICON |