blob: 2f70dbdae7e2813b8f0026e2f5b93a212d9db624 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0-only */
/*
* This file is part of wlcore
*
* Copyright (C) 2011 Texas Instruments Inc.
*/
#ifndef __REG_H__
#define __REG_H__
#define WL18XX_REGISTERS_BASE 0x00800000
#define WL18XX_CODE_BASE 0x00000000
#define WL18XX_DATA_BASE 0x00400000
#define WL18XX_DOUBLE_BUFFER_BASE 0x00600000
#define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000
#define WL18XX_PHY_BASE 0x00900000
#define WL18XX_TOP_OCP_BASE 0x00A00000
#define WL18XX_PACKET_RAM_BASE 0x00B00000
#define WL18XX_HOST_BASE 0x00C00000
#define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000
#define WL18XX_REG_BOOT_PART_START 0x00802000
#define WL18XX_REG_BOOT_PART_SIZE 0x00014578
#define WL18XX_PHY_INIT_MEM_ADDR 0x80926000
#define WL18XX_PHY_END_MEM_ADDR 0x8093CA44
#define WL18XX_PHY_INIT_MEM_SIZE \
(WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR)
#define WL18XX_SDIO_WSPI_BASE (WL18XX_REGISTERS_BASE)
#define WL18XX_REG_CONFIG_BASE (WL18XX_REGISTERS_BASE + 0x02000)
#define WL18XX_WGCM_REGS_BASE (WL18XX_REGISTERS_BASE + 0x03000)
#define WL18XX_ENC_BASE (WL18XX_REGISTERS_BASE + 0x04000)
#define WL18XX_INTERRUPT_BASE (WL18XX_REGISTERS_BASE + 0x05000)
#define WL18XX_UART_BASE (WL18XX_REGISTERS_BASE + 0x06000)
#define WL18XX_WELP_BASE (WL18XX_REGISTERS_BASE + 0x07000)
#define WL18XX_TCP_CKSM_BASE (WL18XX_REGISTERS_BASE + 0x08000)
#define WL18XX_FIFO_BASE (WL18XX_REGISTERS_BASE + 0x09000)
#define WL18XX_OCP_BRIDGE_BASE (WL18XX_REGISTERS_BASE + 0x0A000)
#define WL18XX_PMAC_RX_BASE (WL18XX_REGISTERS_BASE + 0x14800)
#define WL18XX_PMAC_ACM_BASE (WL18XX_REGISTERS_BASE + 0x14C00)
#define WL18XX_PMAC_TX_BASE (WL18XX_REGISTERS_BASE + 0x15000)
#define WL18XX_PMAC_CSR_BASE (WL18XX_REGISTERS_BASE + 0x15400)
#define WL18XX_REG_ECPU_CONTROL (WL18XX_REGISTERS_BASE + 0x02004)
#define WL18XX_REG_INTERRUPT_NO_CLEAR (WL18XX_REGISTERS_BASE + 0x050E8)
#define WL18XX_REG_INTERRUPT_ACK (WL18XX_REGISTERS_BASE + 0x050F0)
#define WL18XX_REG_INTERRUPT_TRIG (WL18XX_REGISTERS_BASE + 0x5074)
#define WL18XX_REG_INTERRUPT_TRIG_H (WL18XX_REGISTERS_BASE + 0x5078)
#define WL18XX_REG_INTERRUPT_MASK (WL18XX_REGISTERS_BASE + 0x0050DC)
#define WL18XX_REG_CHIP_ID_B (WL18XX_REGISTERS_BASE + 0x01542C)
#define WL18XX_SLV_MEM_DATA (WL18XX_HOST_BASE + 0x0018)
#define WL18XX_SLV_REG_DATA (WL18XX_HOST_BASE + 0x0008)
/* Scratch Pad registers*/
#define WL18XX_SCR_PAD0 (WL18XX_REGISTERS_BASE + 0x0154EC)
#define WL18XX_SCR_PAD1 (WL18XX_REGISTERS_BASE + 0x0154F0)
#define WL18XX_SCR_PAD2 (WL18XX_REGISTERS_BASE + 0x0154F4)
#define WL18XX_SCR_PAD3 (WL18XX_REGISTERS_BASE + 0x0154F8)
#define WL18XX_SCR_PAD4 (WL18XX_REGISTERS_BASE + 0x0154FC)
#define WL18XX_SCR_PAD4_SET (WL18XX_REGISTERS_BASE + 0x015504)
#define WL18XX_SCR_PAD4_CLR (WL18XX_REGISTERS_BASE + 0x015500)
#define WL18XX_SCR_PAD5 (WL18XX_REGISTERS_BASE + 0x015508)
#define WL18XX_SCR_PAD5_SET (WL18XX_REGISTERS_BASE + 0x015510)
#define WL18XX_SCR_PAD5_CLR (WL18XX_REGISTERS_BASE + 0x01550C)
#define WL18XX_SCR_PAD6 (WL18XX_REGISTERS_BASE + 0x015514)
#define WL18XX_SCR_PAD7 (WL18XX_REGISTERS_BASE + 0x015518)
#define WL18XX_SCR_PAD8 (WL18XX_REGISTERS_BASE + 0x01551C)
#define WL18XX_SCR_PAD9 (WL18XX_REGISTERS_BASE + 0x015520)
/* Spare registers*/
#define WL18XX_SPARE_A1 (WL18XX_REGISTERS_BASE + 0x002194)
#define WL18XX_SPARE_A2 (WL18XX_REGISTERS_BASE + 0x002198)
#define WL18XX_SPARE_A3 (WL18XX_REGISTERS_BASE + 0x00219C)
#define WL18XX_SPARE_A4 (WL18XX_REGISTERS_BASE + 0x0021A0)
#define WL18XX_SPARE_A5 (WL18XX_REGISTERS_BASE + 0x0021A4)
#define WL18XX_SPARE_A6 (WL18XX_REGISTERS_BASE + 0x0021A8)
#define WL18XX_SPARE_A7 (WL18XX_REGISTERS_BASE + 0x0021AC)
#define WL18XX_SPARE_A8 (WL18XX_REGISTERS_BASE + 0x0021B0)
#define WL18XX_SPARE_B1 (WL18XX_REGISTERS_BASE + 0x015524)
#define WL18XX_SPARE_B2 (WL18XX_REGISTERS_BASE + 0x015528)
#define WL18XX_SPARE_B3 (WL18XX_REGISTERS_BASE + 0x01552C)
#define WL18XX_SPARE_B4 (WL18XX_REGISTERS_BASE + 0x015530)
#define WL18XX_SPARE_B5 (WL18XX_REGISTERS_BASE + 0x015534)
#define WL18XX_SPARE_B6 (WL18XX_REGISTERS_BASE + 0x015538)
#define WL18XX_SPARE_B7 (WL18XX_REGISTERS_BASE + 0x01553C)
#define WL18XX_SPARE_B8 (WL18XX_REGISTERS_BASE + 0x015540)
#define WL18XX_REG_COMMAND_MAILBOX_PTR (WL18XX_SCR_PAD0)
#define WL18XX_REG_EVENT_MAILBOX_PTR (WL18XX_SCR_PAD1)
#define WL18XX_EEPROMLESS_IND (WL18XX_SCR_PAD4)
#define WL18XX_WELP_ARM_COMMAND (WL18XX_REGISTERS_BASE + 0x7100)
#define WL18XX_ENABLE (WL18XX_REGISTERS_BASE + 0x01543C)
#define TOP_FN0_CCCR_REG_32 (WL18XX_TOP_OCP_BASE + 0x64)
/* PRCM registers */
#define PLATFORM_DETECTION 0xA0E3E0
#define OCS_EN 0xA02080
#define PRIMARY_CLK_DETECT 0xA020A6
#define PLLSH_COEX_PLL_N 0xA02384
#define PLLSH_COEX_PLL_M 0xA02382
#define PLLSH_COEX_PLL_SWALLOW_EN 0xA0238E
#define PLLSH_WL_PLL_SEL 0xA02398
#define PLLSH_WCS_PLL_N 0xA02362
#define PLLSH_WCS_PLL_M 0xA02360
#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1 0xA02364
#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2 0xA02366
#define PLLSH_WCS_PLL_P_FACTOR_CFG_1 0xA02368
#define PLLSH_WCS_PLL_P_FACTOR_CFG_2 0xA0236A
#define PLLSH_WCS_PLL_SWALLOW_EN 0xA0236C
#define PLLSH_WL_PLL_EN 0xA02392
#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK 0xFFFF
#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK 0x007F
#define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK 0xFFFF
#define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK 0x000F
#define PLLSH_WL_PLL_EN_VAL1 0x7
#define PLLSH_WL_PLL_EN_VAL2 0x2
#define PLLSH_COEX_PLL_SWALLOW_EN_VAL1 0x2
#define PLLSH_COEX_PLL_SWALLOW_EN_VAL2 0x11
#define PLLSH_WCS_PLL_SWALLOW_EN_VAL1 0x1
#define PLLSH_WCS_PLL_SWALLOW_EN_VAL2 0x12
#define PLLSH_WL_PLL_SEL_WCS_PLL 0x0
#define PLLSH_WL_PLL_SEL_COEX_PLL 0x1
#define WL18XX_REG_FUSE_DATA_1_3 0xA0260C
#define WL18XX_PG_VER_MASK 0x70
#define WL18XX_PG_VER_OFFSET 4
#define WL18XX_ROM_VER_MASK 0x3e00
#define WL18XX_ROM_VER_OFFSET 9
#define WL18XX_METAL_VER_MASK 0xC
#define WL18XX_METAL_VER_OFFSET 2
#define WL18XX_NEW_METAL_VER_MASK 0x180
#define WL18XX_NEW_METAL_VER_OFFSET 7
#define WL18XX_PACKAGE_TYPE_OFFSET 13
#define WL18XX_PACKAGE_TYPE_WSP 0
#define WL18XX_REG_FUSE_DATA_2_3 0xA02614
#define WL18XX_RDL_VER_MASK 0x1f00
#define WL18XX_RDL_VER_OFFSET 8
#define WL18XX_REG_FUSE_BD_ADDR_1 0xA02602
#define WL18XX_REG_FUSE_BD_ADDR_2 0xA02606
#define WL18XX_CMD_MBOX_ADDRESS 0xB007B4
#define WL18XX_FW_STATUS_ADDR 0x50F8
#define CHIP_ID_185x_PG10 (0x06030101)
#define CHIP_ID_185x_PG20 (0x06030111)
/*
* Host Command Interrupt. Setting this bit masks
* the interrupt that the host issues to inform
* the FW that it has sent a command
* to the Wlan hardware Command Mailbox.
*/
#define WL18XX_INTR_TRIG_CMD BIT(28)
/*
* Host Event Acknowlegde Interrupt. The host
* sets this bit to acknowledge that it received
* the unsolicited information from the event
* mailbox.
*/
#define WL18XX_INTR_TRIG_EVENT_ACK BIT(29)
/*
* To boot the firmware in PLT mode we need to write this value in
* SCR_PAD8 before starting.
*/
#define WL18XX_SCR_PAD8_PLT 0xBABABEBE
enum {
COMPONENT_NO_SWITCH = 0x0,
COMPONENT_2_WAY_SWITCH = 0x1,
COMPONENT_3_WAY_SWITCH = 0x2,
COMPONENT_MATCHING = 0x3,
};
enum {
FEM_NONE = 0x0,
FEM_VENDOR_1 = 0x1,
FEM_VENDOR_2 = 0x2,
FEM_VENDOR_3 = 0x3,
};
enum {
BOARD_TYPE_EVB_18XX = 0,
BOARD_TYPE_DVP_18XX = 1,
BOARD_TYPE_HDK_18XX = 2,
BOARD_TYPE_FPGA_18XX = 3,
BOARD_TYPE_COM8_18XX = 4,
NUM_BOARD_TYPES,
};
enum wl18xx_rdl_num {
RDL_NONE = 0,
RDL_1_HP = 1,
RDL_2_SP = 2,
RDL_3_HP = 3,
RDL_4_SP = 4,
RDL_5_SP = 0x11,
RDL_6_SP = 0x12,
RDL_7_SP = 0x13,
RDL_8_SP = 0x14,
_RDL_LAST,
RDL_MAX = _RDL_LAST - 1,
};
/* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */
#define WL18XX_PHY_FPGA_SPARE_1 0x8093CA40
/* command to disable FDSP clock */
#define MEM_FDSP_CLK_120_DISABLE 0x80000000
/* command to set ATPG clock toward FDSP Code RAM rather than its own clock */
#define MEM_FDSP_CODERAM_FUNC_CLK_SEL 0xC0000000
/* command to re-enable FDSP clock */
#define MEM_FDSP_CLK_120_ENABLE 0x40000000
#endif /* __REG_H__ */